• +1 (415) 818-0845
  • inquiries-usa@perma-batteries.com
Facebook Youtube Linkedin
  • Sigenergy
  • Edison battery
  • Guides
Products — SIGENERGY
SIGENERGY EC ControllerField programmable · 11 kW max · 120/240 VAC split phase Sigen Loading HubSplit phase · load management & backup transfer SigenStor BAT 9.0Stackable battery modules · 9 kWh each Sigen EV DC ChargerBidirectional DC charging · V2H ready View all All-in-one systems
Resources
Operation manualsUser & installer manuals, firmware notes Certificates & listingsUL, NEC compliance, spec sheets How to installStep-by-step guides, commissioning, app setup Schematics & wiringSingle-line diagrams, grid-tied & off-grid

Browse all resources

Not sure what size you need?

Size your off-grid SIGENERGY system in 2 minutes based on your loads, location and sun hours.

Off-grid solar simulator
Victron + Edison bundles
Edison 12V kit— Victron Edison 24V kit— Victron Edison 48V kit— Victron
Sol-Ark + Edison bundles
Edison 48V kit— Sol-Ark
Bare batteries
Edison batteries— cells & packs, no inverter
Documentation
Datasheet & specifications Installation manual Maintenance & electrolyte Charge settings (Victron / Sol-Ark) Warranty & certifications

Which Edison battery for your project? Our simulator guides you based on your loads, your site and your budget.

Solar simulator
Solar batteries
Battery chemistries compared— LFP, NiFe, LTO How to size an off-grid battery bank Lifespan & cycle life BMS & pack safety Off-grid solar 101
Wiki & documentation
SIGENERGY— EC Controller, SigenStor Edison batteries Sol-Ark Victron
Inverters
Off-grid vs hybrid inverter MPPT, how it works AC vs DC coupling Split phase 120/240 V explained Generator backup & auto-start
Codes & regulations
Where can I install my batteries? NEC for stand-alone systems— Art. 690, 706, 710 UL 9540 / 9540A, what it means Permits & inspections (AHJ) 30% federal tax credit (ITC)— off-grid eligible Canada: CSA & CEC basics

Not sure where to start? Our technical guides break down every choice, spec sheet in hand.

All guides Solar simulator
$0.00 0 Cart
Need a quote ?
Edison batteries
October 7, 2025
SIGENERGY EC SP
SIGENERGY Sigenstor EC SP
October 21, 2026
12V EDISON OFF GRID SOLAR KIT

48V Victron off-grid pre-wired (120V)

Pre-wired off-grid board · 120 V single-phase

SUNCONNECT US 120 V single-phase · Victron off-grid solar kit 48 V
1 × MultiPlus-II 48/5000/70-95 120 V · SmartSolar MPPT 250/100 · Cerbo GX · off-grid sites only · built for the Edison nickel-iron battery
⚡4,000 W continuous
9 kW peak
🔌120 V single-phase
1 × MultiPlus-II 48/5000/70-95 120 V
☀️5,800 W of solar · 250 V string
SmartSolar MPPT 250/100-Tr VE.Can
🔋Edison battery ready ·  Or lithium and lead-acid, 48 V
🛢️95 A generator transfer
PowerAssist · auto start/stop · 120 V generator
🛡️Class T 250 A + NEC protection
DC/AC breakers, SPD type 2, disconnects
📊Cerbo GX + GX Touch · SmartShunt
free VRM remote monitoring
✅UL 1741 · UL 458 · CSA C22.2
listed inverter and controller
🔧Wired, tested, programmed
nickel-iron profile loaded in our workshop
Need a system design? →
Category: SUNCONNECT
Share
0
  • Description
  • Reviews 0

SUNCONNECT US 120 V: the pre-wired Victron off-grid solar kit with one MultiPlus-II 48/5000

1 × MultiPlus-II 48/5000/70-95 120 V · SmartSolar MPPT 250/100-Tr VE.Can · Cerbo GX + GX Touch · NEC-rated DC and AC protection · single-phase 120 V output · assembled, wired and programmed in our workshop

Off-grid only4,000 W continuous9 kW peak5,800 W PV · 250 V120 V single-phaseUL 1741 · CSA C22.2Edison battery readyPre-programmed
🏕️Designed for off-grid sites only.
This board builds its own 60 Hz grid from the battery and the PV array. The AC input is reserved for a generator. It is not configured for grid-interactive or export operation. Need 240 V loads? See the split-phase 120/240 V version.
MultiPlus-II 120 V datasheet
SmartSolar MPPT 250/100 datasheet
UL 1741 / CSA certificate
Victron off-grid kit

The Victron off-grid solar kit 120V at a glance

ConfigurationSUNCONNECT US 120 V single-phase · 1 × MultiPlus-II 48/5000/70-95
Continuous AC power at 77 °F4,000 W (5,000 VA)
Peak power9,000 W
AC output120 V · 60 Hz
Solar charge controllerSmartSolar MPPT 250/100-Tr VE.Can · 100 A · 5,800 W nominal PV at 48 V · 250 V max.
Generator input120 V generator, 95 A · PowerAssist · auto start/stop
Battery charging70 A from generator + 100 A solar · 170 A total
Battery48 V Edison nickel-iron bank, 40 cells, 100 to 1,200 Ah · also lithium or lead-acid
MonitoringCerbo GX + GX Touch 50 · SmartShunt 500 A · free VRM portal · VictronConnect Bluetooth
ProtectionClass T 250 A · PV disconnect and string fuses · type 2 DC and AC surge protection · AC breakers · per NEC 690, 706 and 710
CertificationsMultiPlus-II: UL 1741, UL 458, CSA C22.2 No. 107.1 · MPPT: UL 1741, CSA C22.2, EN/IEC 62109-1
Deliverywired, tested and programmed on a mounting board · freight truck

The Victron off-grid solar kit 120V is a complete power plant on a board, built for sites with no utility connection and no 240 V loads. First, one MultiPlus-II 48/5000/70-95 120 V inverter-charger produces a 4,000 W single-phase house grid and charges from a generator. Then, a SmartSolar MPPT 250/100 brings in up to 5,800 W of solar on a 250 V string. Moreover, a Cerbo GX with a touch screen and a SmartShunt watches the battery. That matters on an Edison nickel-iron bank, which has no BMS of its own. Finally, every breaker, fuse and surge protector is sized and wired in our workshop. The whole system is programmed for your battery before it ships. In short, you connect the panels, the battery and the loads, and you turn it on.

“An Edison battery has no BMS, so the inverter and the charge controller are the BMS. That is why we insist on the Victron platform for these kits: every voltage threshold is adjustable, the SmartShunt gives a true state of charge, and the Cerbo lets us check the bank from the workshop. The pre-wiring is the easy part. The programming is what keeps a nickel-iron bank healthy for twenty-five years.”
— Julien, Perma Batteries
victron off-grid MPPT

One MultiPlus-II, 120 V: 4,000 W continuous, 9 kW peak

The 120 V version uses a single MultiPlus-II 48/5000/70-95 and delivers 4,000 W continuously at 77 °F, 3,700 W at 104 °F. First, that covers a cabin, a workshop, a tiny home or a house where every appliance runs on 120 V. Then, the 9,000 W peak starts a refrigerator compressor, a 1 hp pump or a circular saw. Moreover, the 95 A transfer switch accepts a 120 V generator and charges the bank at 70 A. However, there is no 240 V output on this board. A well pump, a dryer or a 240 V mini-split needs the split-phase version with two inverters.

Parameter120 V single-phase kit
Inverter-charger1 × MultiPlus-II 48/5000/70-95 120 V
Continuous power at 77 / 104 / 149 °F4,000 / 3,700 / 3,000 W
Peak power9,000 W
AC output120 V · 60 Hz · single-phase
Generator transfer95 A at 120 V
Generator charge current70 A
Solar charge current100 A (second MPPT optional)
Total charge current170 A
Zero-load consumption15 W · 10 W AES · 3 W search
Inverter weight71 lb

💡 What it means for you

Add up the loads that can start at the same time. If the total stays under 4 kW and nothing needs 240 V, this is the right board. If you later add a 240 V load, a second MultiPlus-II can be added on site and the pair reconfigured in split-phase, with a larger Class T fuse.

MultiPlus-II 48/5000/70-95 120 V: inverter, charger and transfer switch

The MultiPlus-II is the heart of the Victron off-grid solar kit 120V. First, it is a true sine-wave inverter rated 5,000 VA, with a 9,000 W peak for motor starts. Then, it is a 70 A battery charger with a four-stage adaptive algorithm and a temperature sensor. Moreover, it holds a 95 A transfer switch for the generator, with PowerAssist. When loads exceed what the generator can supply, the battery adds the difference. As a result, a 4 kW portable generator runs a house that briefly needs 8 kW. Finally, it is UL 1741 and UL 458 listed, and certified to CSA C22.2 No. 107.1 for Canada.

FunctionRating per unitPractical reading
Inverter5,000 VA · 4,000 W at 77 °F · 96 % efficiencyruns a 1 hp well pump or a 12,000 BTU mini-split
Peak9,000 Wmotor and compressor starts
Charger70 A at 57.6 V absorption · 55.2 V floatreprogrammed for nickel-iron
Transfer switch95 A · 90 to 140 VAC · 55 to 65 Hzaccepts a poorly regulated generator
Auxiliary output48 A, live only on generatorwater heater or EV charger on generator only
Programmable relay120 V / 4 A · 35 VDC / 4 Agenerator auto start/stop on SOC
DC input38 to 66 V40-cell Edison bank window
Zero-load15 W · 10 W AES · 3 W searchsmall overnight drain

SmartSolar MPPT 250/100-Tr VE.Can: 5,800 W of solar on a 250 V string

Solar charging is handled by a dedicated controller, so the PV array is sized independently of the inverter. First, the SmartSolar MPPT 250/100 accepts up to 250 V open-circuit, 245 V in operation. That allows strings of five or six 60-cell modules. Then, it delivers 100 A at 48 V, or 5,800 W of nominal PV. Moreover, its ultra-fast tracking and partial-shading algorithm hold the true maximum power point under moving clouds. Efficiency exceeds 99 % without a fan. Finally, the VE.Can port synchronizes charging across up to 25 controllers and connects to the Cerbo GX. The charge algorithm is fully programmable, including equalization and temperature compensation. An Edison bank needs both.

ParameterValuePractical reading
Rated charge current100 A5,800 W nominal PV at 48 V
Max. PV open-circuit voltage250 V (245 V operating)5 to 6 modules of 60 cells in series, cold-corrected
Max. PV short-circuit current70 A (30 A per MC4 pair)up to 3 strings in parallel with fuses
Max. efficiency99 %no fan, no filter
Absorption / float / equalization57.6 / 55.2 / 64.8 V default, adjustablenickel-iron profile loaded before shipping
Temperature compensation-64 mV/°C at 48 Vwith external sensor via Cerbo or SmartShunt
CommunicationVE.Can · VE.Direct · BluetoothCerbo GX, VictronConnect app
Terminals35 mm² / 2 AWG (Tr model)screw terminals, no MC4 on the controller
Weight9.9 lb (4.5 kg)wall-mounted on the board
victron off-grid MPPT

⚡ The Perma Batteries tip

Oversize the array. The controller clips at 5,800 W, but 7,000 to 8,000 W of panels on the string fills the battery earlier in the morning and on cloudy winter days, at no risk to the controller. Keep the cold-corrected Voc under 245 V: in a -4 °F climate, six 60-cell modules is the limit; use five.

Built for the Edison battery: 40 cells, no BMS, fully programmable charging

An Edison nickel-iron bank is the reason this board exists. First, 40 cells of 1.2 V make a 48 V bank, from 100 to 1,200 Ah, up to 55 kWh. Then, the bank has no BMS, so the inverter and the controller enforce every threshold. We program absorption at 1.60 V per cell, 64 V on the bank, with float around 1.45 V per cell. Moreover, the SmartShunt provides the state of charge that a nickel-iron cell’s flat voltage curve cannot. The Cerbo GX triggers the generator from that reading. Finally, the kit remains battery-agnostic. The same board runs a lithium rack with a BMS on the Cerbo, or a lead-acid bank, with a different charge profile.

BankCellsNominal energyC/5 charge currentMatches
48 V · 200 Ah40 × 200 Ah9.6 kWh40 Aweekend cabin
48 V · 400 Ah40 × 400 Ah19.2 kWh80 Afull-time cabin or small home
48 V · 600 Ah40 × 600 Ah28.8 kWh120 Ahome with 2 days of autonomy

⚠️ The 66 V ceiling

The MultiPlus-II accepts 38 to 66 V on the DC side. A 40-cell Edison bank in absorption at 1.65 V per cell reaches 66 V, right at the limit. That is why we set absorption at 1.60 V per cell (64 V) and handle periodic equalization under supervision, with the inverter paused. Do not raise the absorption voltage without asking us.

The Victron system can be either attached to an Edison battery array, or a compatible lithium-battery solution such as the DISCOVER HELIOS ESS.

split-phase off-grid solar kit

DC and AC protection, sized to NEC 690, 706 and 710

Every conductor on the board is protected at its source. We follow the National Electrical Code articles for PV, energy storage and stand-alone systems. First, the battery feeds a Class T fuse of 250 A with a 20,000 A interrupt rating and a DC disconnect, close to the terminals. Then, the inverter and the MPPT get their own branch fuses on a Lynx Distributor busbar. Moreover, the PV side carries a 600 V DC disconnect, string fuses and a type 2 DC surge protector. Finally, the AC side has a type 2 surge protector, a generator input breaker and output breakers in a listed enclosure. The board ships with a one-line diagram and a wiring schedule for the inspector.

CircuitDeviceRatingCode reference
Battery mainClass T fuse + DC disconnect250 A · 20 kA AICNEC 706.15, 240.67
Inverter branchMEGA fuse on Lynx Distributor200 ANEC 706.21
MPPT outputMEGA fuse on Lynx Distributor125 ANEC 690.9
PV stringsDC fuse holders, 1,000 V15 or 20 A per string, per module ratingNEC 690.9
PV disconnectDC-rated switch600 V · 32 ANEC 690.13, 690.15
PV surgeType 2 DC SPD600 V · 40 kANEC 690.7, 242
Generator inputBreaker100 A single-pole, 120 VNEC 702, 710
Inverter outputBreakers40 A main + 50 A auxiliaryNEC 710.15
AC surgeType 2 AC SPD120 V · 40 kANEC 242
GroundingGround bar, lugs, GFDI in MPPTEGC sized per NEC 250.122NEC 690.41, 250

✅ Advantage: listed components, one schematic

Fuses, breakers, busbars and surge protectors are UL-listed products from Littelfuse, Midnite Solar, Victron and Citel. With the UL 1741 inverter and the CSA-certified controller, the board is built from listed parts and documented for permit review in any state or province. Final approval remains with your local AHJ.

Cerbo GX, GX Touch and VRM: monitoring and remote support

Every kit ships with a Cerbo GX and a GX Touch 50 screen. First, the Cerbo collects the inverter, the MPPT and the SmartShunt on one dashboard. Then, the touch screen shows energy flows, state of charge and alarms on the wall. Moreover, with any internet connection, the free VRM portal keeps the history and sends alerts. Our technicians can adjust a setting without a site visit. Finally, VictronConnect over Bluetooth gives local access to the MPPT and the shunt from a phone. No network is needed.

💡 Three levels of control

Local: GX Touch and VictronConnect over Bluetooth. On site: VEConfigure through the MK3-USB interface for fine settings. Remote: VRM for history, alerts, firmware updates and remote configuration. Each person involved gets the right tool.

What is in the 120 V single-phase kit

  1. Victron MultiPlus-II 48/5000/70-95 120 V × 1, UL 1741, UL 458, CSA C22.2 No. 107.1
  2. Victron SmartSolar MPPT 250/100-Tr VE.Can × 1, UL 1741, CSA C22.2
  3. Cerbo GX × 1 and GX Touch 50 × 1
  4. SmartShunt 500 A × 1 with battery temperature sensor
  5. Lynx Distributor × 1, 1,000 A busbar with MEGA fuses for each branch
  6. Class T battery fuse 250 A and DC disconnect, 20 kA AIC
  7. PV protection: 600 V DC disconnect, string fuse holders, type 2 DC surge protector
  8. AC protection: generator input breaker 100 A single-pole, 120 V, output breakers 40 A main + 50 A auxiliary, type 2 AC surge protector, listed enclosure
  9. VE.Bus and VE.Can cables, MK3-USB interface, external AC current sensor 100 A
  10. Mounting board, 2 AWG battery cables, ground bar, labels
  11. One-line diagram, wiring schedule and configuration report for the inspector

🔧 What you still do on site

Mount the board, run the PV strings to the disconnect, connect the battery to the Class T fuse, land the generator and the house panel on the AC breakers. Crimping, fuse sizing and VEConfigure settings are already done. We walk you through commissioning by phone or video.

Why choose a pre-wired Victron off-grid solar kit 120V?

  1. Installation twice as fast as loose components, with the wiring already torqued and tested.
  2. Code-ready protection: fuses, disconnects and surge protection sized per NEC 690, 706 and 710.
  3. Listed hardware: UL 1741 inverter, CSA-certified controller, UL-listed fuses and breakers.
  4. Programmed for your battery before shipping, nickel-iron profile included.
  5. Open ecosystem: VE.Bus, VE.Can, free VRM, public documentation, long firmware support.
  6. Expandable: add a second MPPT, add a second inverter for split-phase, grow the battery bank.
  7. Repairable: every component is a standard Victron or Midnite part, replaceable individually.
  8. Remote support through VRM from our workshop, wherever the site is.

Victron off-grid solar kit 120V datasheet

Kit nameSUNCONNECT US 120 V single-phase · pre-wired Victron off-grid solar kit · 48 V
Applicationoff-grid, stand-alone systems only · generator as backup source
ConfigurationSUNCONNECT US 120 V single-phase · 1 × MultiPlus-II 48/5000/70-95
Inverter-chargerVictron MultiPlus-II 48/5000/70-95 120 V · PMP482505120 · × 1
Continuous output at 77 / 104 / 149 °F4,000 W / 3,700 W / 3,000 W
Peak power9,000 W
Output voltage / frequency120 V · 60 Hz
Max. efficiency96 %
Zero-load power15 W (10 W AES, 3 W search)
AC input (generator)90 to 140 VAC per leg · 55 to 65 Hz · 95 A at 120 V
Charger70 A total · absorption 57.6 V · float 55.2 V · storage 52.8 V (defaults, reprogrammed for nickel-iron)
DC input range38 to 66 V
Auxiliary AC output48 A per unit, active on generator only
Programmable relay120 V / 4 A AC · 4 A to 35 VDC · 1 A to 60 VDC
Inverter protectionoutput short circuit · overload · battery high / low · over temperature · 120 VAC on output · DC ripple
Inverter dimensions / weight26.6 × 13.0 × 6.5 in (676 × 330 × 164 mm) · 71 lb (32 kg)
Inverter listingsUL 1741 · UL 458 · CSA C22.2 No. 107.1-16 · EN-IEC 60335-1 / -2-29
Solar charge controllerVictron SmartSolar MPPT 250/100-Tr VE.Can
Rated charge current / nominal PV100 A · 5,800 W at 48 V
Max. PV voltage250 V absolute · 245 V start-up and operating
Max. PV short-circuit current70 A
MPPT efficiency / self-consumption99 % · 20 mA at 48 V
MPPT charge voltagesabsorption 57.6 V · float 55.2 V · equalization 64.8 V (defaults, adjustable)
MPPT protectionPV reverse polarity · output short circuit · over temperature · IP43 / IP22
MPPT dimensions / weight8.5 × 11.6 × 4.1 in (216 × 295 × 103 mm) · 9.9 lb (4.5 kg)
MPPT listingsUL 1741 · CSA C22.2 · EN/IEC 62109-1
MonitoringCerbo GX · GX Touch 50 · SmartShunt 500 A · VRM portal · VictronConnect
Battery main protectionClass T fuse 250 A · 20 kA AIC · DC disconnect
Branch protectionLynx Distributor · MEGA fuses 200 A per inverter, 125 A for MPPT
PV protection600 V DC disconnect · string fuses 15 / 20 A · type 2 DC SPD 600 V
AC protectiongenerator input breaker 100 A single-pole, 120 V · output breakers 40 A main + 50 A auxiliary · type 2 AC SPD
Battery cables2 AWG battery cables
Compatible batteriesEdison nickel-iron 48 V (40 cells) · lithium 48 V with BMS · lead-acid 48 V
WarrantyVictron 5 years on inverter and controller · workshop assembly 2 years
Deliveryassembled, tested and programmed · freight truck

FAQ — Victron off-grid solar kit 120V

What is the SUNCONNECT Victron off-grid solar kit 120V?
A pre-wired board combining one Victron MultiPlus-II 48/5000/70-95 120 V inverter-charger, a SmartSolar MPPT 250/100 solar charge controller, Cerbo GX monitoring and all DC and AC protection. It is assembled, tested and programmed in our workshop for a 48 V battery bank, Edison nickel-iron by default.
Is 120 V single-phase enough for my site?
Yes, if every load is 120 V and the loads that can start together stay under 4 kW: cabins, workshops, tiny homes and many small houses. Any 240 V appliance, such as a well pump, a dryer or a mini-split, requires the split-phase version with two inverters.
Can this kit be connected to the utility grid?
No. It is configured for stand-alone operation only. The AC input is reserved for a generator. Grid-interactive use would require a different configuration and a utility interconnection agreement.
How much solar can I connect?
The MPPT 250/100 delivers 5,800 W at 48 V from a string up to 245 V in operation. You can oversize the array to 7 to 8 kW for better winter yield; the controller simply clips. A second MPPT doubles the solar input and is available as an option.
Why an Edison nickel-iron battery with a Victron system?
A nickel-iron bank has no BMS, so every charge threshold must be set in the inverter and the controller. Victron equipment allows that, and the SmartShunt provides an accurate state of charge. We ship the kit programmed with the nickel-iron profile, absorption at 1.60 V per cell.
Does the kit work with lithium or lead-acid batteries?
Yes. The board is battery-agnostic. A 48 V lithium rack connects its BMS to the Cerbo GX; a lead-acid bank uses a dedicated charge profile. Tell us the battery at order and we program it.
Is the kit code-compliant in the United States and Canada?
The inverter is UL 1741 and UL 458 listed and certified to CSA C22.2 No. 107.1; the controller is UL 1741 and CSA C22.2 certified. Fuses, breakers, busbars and surge protectors are UL-listed, sized per NEC 690, 706 and 710, and documented on a one-line diagram. Final approval rests with your local authority having jurisdiction.
Can I run a generator with it?
Yes. The MultiPlus-II has a 95 A transfer switch and a programmable relay that starts and stops the generator on battery state of charge. PowerAssist adds battery power to the generator during peaks, so a 4 kW generator can serve a house that briefly needs 8 kW. A 120 V generator is enough for this version.

Reviews

There are no reviews yet.

Be the first to review “48V Victron off-grid pre-wired (120V)” Cancel reply

Your email address will not be published. Required fields are marked *

You may also like…

  • AES RACKMOUNT 48-48-5120

    Discover AES Rackmount 48-5120

  • DISCOVER HELIOS ESS

    Discover HELIOS ESS

Related products

  • split-phase off-grid solar kit

    48V Victron off-grid pre-wired split-phase (240V)